
Extreme Adhesives offers a product line of solvent and silicone free, Structural Methyl Methacrylate Adhesives (MMA) materials specifically formulated for use with Cellular PVC Board used in commercial and residential construction as well as in the marine and sign industries. These products offer a range of cure times and viscosities to meet each application whether it’s installation, assembly or fabrication. Extreme’s PVC TrimWelder is the only product to be recommended / certified for use with every major cellular PVC manufacturer in North America, including: Azek, Koma, Kleer, Versatex, Certainteed, Trex, Tuff Board, etc.
PVC TrimWelder® will bond and fill all PVC building materials with a single fast or slow curing adhesive. It's stronger then the PVC you're bonding! It will bond aluminum or stainless steel brackets and fittings. It's bright white and completely weatherproof. Use Fast Cure to seal and smooth cut ends and edges to prevent discoloration from dirt or mildew. It won't attract dust and dirt like caulks, it fills gaps, cuts, and dents and it doesn't have any toxic solvents.
PVC TrimWelder® meets or exceeds all California Air Resource Board and United States Federal VOC emissions standards when properly mixed and cured!
PVC TrimWelder® sands and finishes just like the PVC your used to working with!
TrimWelder Properties »
PVC TrimWelder - Fast Cure
PVC TRIMWELDER™ FAST CURE Adhesive is a rapid curing, two-component adhesive formulated and colored for PVC Trim Board applications with a work life of 4 - 7 minutes at 70ş F after mixing. It is a creamy, medium viscosity, solvent-free structural adhesive that is EPA and CARB compliant. Cured performance shows excellent adhesion and bond strength. Adhesive joints are ready to handle in 10-30 minutes.
PVC TRIMWELDER™ FAST CURE Adhesive does not require special surface preparation. It’s stronger then PVC after curing and fills gaps to 1/8”. FAST CURE actually reinforces core to core joints without the need for fasteners or biscuits. The creamy consistency, won’t foam, run or drip and is well suited to seal and smooth cut edges for a finished look. Excellent sandability after curing.
Why Should You Select This Adhesive?
- Permanent Unitizing Structural Adhesive
- Excellent Adhesion to PVC
- Impact Resistance - Peel Strength
- Matches white PVC Trim Boards
- Paintable
- Fast Setting
- Easy to apply
- Fills Nail Holes and Gaps
- Meets 2009 EPA VOC & CARB requirements
- Application Temp: 25F to 100F
- Work Time (Minutes): 4 to 7
- Color: Bright White
- Viscosity: Medium/Creamy
- Elongation: Moderate
- Mix Ratio by Volume: 1:1
Packaging: 50ml, 220ml
ItemNumber: EXT-FC-50-ML, EXT-FC-220-ML
More »
PVC TrimWelder - Slow Cure
PVC TRIMWELDER™ SLOW CURE Adhesive is a slower curing, two-component adhesive formulated and colored for PVC Trim Board applications with a work life of 15 to 25 minutes at 70ş F after mixing. It is a creamy, medium viscosity, solvent-free structural adhesive that is EPA and CARB compliant. Cured performance shows excellent adhesion and bond strength. Adhesive joints are ready to handle in 90 to 120 minutes.
PVC TRIMWELDER™ SLOW CURE Adhesive does not require special surface preparation. It’s stronger then PVC after curing and fills gaps to 1/4”. SLOW CURE is designed for larger parts requiring additional assembly time or as a finishing material to create fillets and blends . The creamy consistency, won’t foam, run or drip Excellent sandability after curing. NOTE! For best structural core to core bonds we recommend PVC TRIMWELDER™ FAST CURE
Why Should You Select This Adhesive?
- Permanent Unitizing Structural Adhesive
- Excellent Adhesion to PVC
- Impact Resistance - Peel Strength
- Matches white PVC Trim Boards
- Paintable
- Fast Setting
- Easy to apply
- Fills Nail Holes and Gaps
- Meets 2009 EPA VOC & CARB requirements
- Application Temp: 45F to 115F
- Work Time (Minutes): 20 to 25
- Color: Bright White
- Viscosity: Medium/ Creamy
- Elongation: Moderate
- Mix Ratio by Volume: 1:1
Packaging: 50ml, 220ml
ItemNumber: EXT-SC-50-ML, EXT-SC-220-ML
More »
PVC TrimWelder - Laminating Grade
The Laminator Laminating Grade Adhesive is a lower viscosity, solvent-free structural adhesive system designed for laminating unmilled PVC sheets and boards. The Laminator Adhesive is a moderate cure speed two-component product with an open time of 15 minutes at 70ş F after mixing. Its lower viscosity provides greater flow-out with less clamping pressure to insure a thin, void free bond. The Laminator Adhesive does not require special surface preparation. Do Not remove the skin of the cellular PVC. Our Laminating Grade System is so strong, it appears to weld the PVC together. The creamy consistency won’t foam and spreads easily. See Data Sheet for complete instructions. PVC TrimWelder The Laminator Adhesive is ready to handle in 45 minutes and may be cut and machined in 1 Hour.
Why Should You Select This Adhesive?
- Permanent Unitizing Structural Adhesive
- Excellent Adhesion to Plastics And Metals
- Impact Resistance - Peel Strength
- Matches white PVC Trim Boards
- Paintable
- Moderate Cure Speed
- Thinner Bonds use Less Adhesive
- Application Temp: 60F to 115F
- Work Time (Minutes): 10 to 15
- Color: Bright White
- Viscosity: Low
- Elongation: Moderate
- Mix Ratio by Volume: 1:1
Packaging: 220, 400, and 1500 ml cartridges
Item Number: EXT-LG-220ML
More »
Fill & Flex PVC Adhesive Sealant
PVC TrimWelder tm Fill & Flex is a bright white, non yellowing flexible adhesive sealant for PVC Trim.
Fill and Flex is a urethane based, one part, PVC adhesive / sealant with premium grade TiO2 pigments. It resists long term yellowing even outdoors and unpainted! It has a high level of flexibility and elongation which makes it perfect to absorb expansion and contraction from heat and cold. It's supplied in a convenient 10.3 oz caulking tube. The slow curing properties of Fill & Flex allow ample work time and make it perfect for "after installation" finishing Fill & Flex is also paintable!
- Application Temp: 45F to 115F
- Work Time (Minutes): 5 to 15
- Color: White
- Viscosity: Medium/ Creamy
- Elongation: High
- Mix Ratio by Volume: NA (1 component)
Packaging: 300ml
Item Number: EXT-FF-300ML
More »
White Hot One Part Thick and White PVC Trim Adhesive
One Part White Hot Adhesive for PVC Trim and Moulding. Thick, creamy, and bright white for joining PVC to itself.
This thick, creamy, and bright white solvent based adhesive is just the thing for joining PVC to itself when you don't need the super strength and faster curing of our structural grades. It's packaged in a convenient 5 oz squeeze tube with a resealable cap.
- Application Temp: 45F to 115F
- Work Time (Minutes): 3 to 5
- Color: White
- Viscosity: Low
- Elongation: Low
- Mix Ratio by Volume: NA (1 component)
Packaging: 5 oz.
Item Number: EXT-WHOT-5OZ
More »